![]() To view the default settings, you can look at the apigee-monit component configurationįiles. Of times to retry a service before triggering a failure response.īy default, apigee-monit monitors all Edge components on a node using their pre-defined componentĬonfigurations. Component configurations can also define how often to check a service and the number TERMINOLOGYĬomponent configuration specifies the service to check and the action to take in the event * While not technically supported, you can install and useĪpigee-monit on CentOS/RHEL/Oracle version 6.9 for Apigee Edge for Private Cloud version 4.19.01.Īpigee-monit uses component configurations to determine which components to monitor, whichĪspects of the component to check, and what action to take in the event of a failure. (The supported OSįor apigee-monit depends on the version of Private Cloud.) Operating System The following image shows the apigee-monit architecture in a 5-node cluster: Figure 1: A separate instance of apigee-monit runs in isolation on each node in aĪpigee-monit supports the following platforms for your Private Cloud cluster. These separate apigee-monit instances operate independently of oneĪnother: they do not communicate the status of their components to the other nodes, nor do theyĬommunicate failures of the monitoring utility itself to any central service. Of apigee-monit on each node in your cluster. apigee-monit architectureĭuring your Apigee Edge for Private Cloud installation and configuration, you optionally install a separate instance ![]() Providing a variety of services, including:Īpigee recommends that you monitor apigee-monit to ensure that it is running. About apigee-monitĪpigee-monit helps ensure that all components on a node stay up and running. opt/apigee/apigee-service/bin/apigee-service apigee-monit report /opt/apigee/apigee-service/bin/apigee-service apigee-monit summaryĬat /opt/apigee/var/log/apigee-monit/apigee-monit.logĮach of these topics and others are described in detail in the sections that follow. opt/apigee/apigee-service/bin/apigee-service apigee-monit monitor -c component_name /opt/apigee/apigee-service/bin/apigee-service apigee-monit monitor -c all ![]() opt/apigee/apigee-service/bin/apigee-service apigee-monit unmonitor -c component_name /opt/apigee/apigee-service/bin/apigee-service apigee-monit unmonitor -c all This installs apigee-monit and starts monitoring all components on the node by default. opt/apigee/apigee-service/bin/apigee-service apigee-monit configure /opt/apigee/apigee-service/bin/apigee-service apigee-monit start opt/apigee/apigee-service/bin/apigee-service apigee-monit install To install apigee-monit, do the following steps: If you are using Amazon Linux, first install Fedora. This section shows you how to quickly get up and running with apigee-monit. Task that requires you to stop a component.Īs a result, you must stop monitoring the component beforeĮxecuting any procedure that requires you to install, upgrade, stop, or restart a component.īy default, apigee-monit checks the status of Edge services every 60 seconds. ![]() A component fails a check when it isĭisabled, but also when you purposefully stop it, such as during an upgrade, installation, or any It is not part of theĬomponent every time the component fails a check. To use apigee-monit, you must install it manually. BeforeĬontinuing, check the list of compatible platforms. NOTE: apigee-monit is not supported on all platforms. Polls Edge services if a service is unavailable, then apigee-monit attempts to restart it. Apigee Edge for Private Cloud includes apigee-monit, a tool based on the open source
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |